process_reflowoven

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Last revisionBoth sides next revision
process_reflowoven [2022/04/10 13:44] benhprocess_reflowoven [2022/06/12 15:37] benh
Line 2: Line 2:
 ===Table of Contents=== ===Table of Contents===
   - What is a reflow oven?   - What is a reflow oven?
-  - How to use the reflow oven+  - How to use the reflow oven (Basics) 
 +  - Advanced reflow use - software, temperature monitoring, and custom recipes
  
 ---- ----
Line 10: Line 11:
  
 ---- ----
-===How to use the reflow oven=== +===How to use the reflow oven (Basics)=== 
-The Hive's reflow oven, the [[https://www.lpkfusa.com/datasheets/prototyping/protoflow.pdf|LPKF ProtoFlow ]], is located in the Semi-Clean room on the lower level of the IDC in Van Leer. It looks like a large rectangular box in the far corner of the room. It's connected to a computer that can theoretically provide higher-precision information and control over the oven, but that's beyond the scope of this writeup. Feel free to experiment if you'd like.+The Hive's reflow oven, the [[https://www.lpkfusa.com/datasheets/prototyping/protoflow.pdf|LPKF ProtoFlow S N2]], is located in the Semi-Clean room on the lower level of the IDC in Van Leer. It looks like a large rectangular box in the far corner of the room. It's connected to a computer that can theoretically provide higher-precision information and control over the oven, but that's beyond the scope of this writeup. Feel free to experiment if you'd like.
  
 The oven has a power button on the front of the tool, and a small screen with four arrow keys on the top. That's it. The oven has a power button on the front of the tool, and a small screen with four arrow keys on the top. That's it.
 +
 +There is no training required to use the oven.
  
 To operate (images below): To operate (images below):
-  - Make sure that your board is populated with solder paste and components prior to starting the ovenDo not place any soft plastic components such as connectors onto the board because they will likely melt in the oven! If you're concerned, check with the datasheets about their maximum storage temperature/maximum reflow temperature. The lead-free profiles will reach 290C.  +  - Apply solder paste to the pads of your board (usually with a stencil) and populate your board with all surface-mount components. Leave off components that cannot be reflowed, e.g. connectors. Check all datasheets if youre unsure! Default lead-free profile reaches 270C, leaded reaches 230C.  
-  - Power on the oven by pressing the power button on the front of the tool.+  - Power on the oven by pressing the power button on the front of the tool. 
   - Using the arrow keys and the screen, navigate to the profile you'd like to run.    - Using the arrow keys and the screen, navigate to the profile you'd like to run. 
-      - If you used lead-free solder paste like was recommended in the stencil write-up"LF-MEDIUM" will be fineThe difference between sizes and between LF vs. LF-2 is unclear+     - If you used lead-free solder paste, select “HIVE_LF”(Temperature profile given below.) 
-      - If you used a leaded solder paste, you can try the "PB-MEDIUM" profile, but YMMV+     - If you used a leaded solder paste, select “HIVE_PB”. (Temperature profile given below.) 
-  - Press the right arrow key to select the profile, and then the up arrow key to highlight "OPEN/CLOSE". Press the right arrow key to open the drawer. +  - Press the right arrow key to select the profile, the up-arrow key to highlight OPEN/CLOSE”, and the right arrow key to open the drawer. 
-  - Once the drawer is open, adjust the metal bars inside (they're magnetic) to be the correct spacing so that your PCB sits on their edges safely. When that's done, remove your PCB and press the right arrow key to close the drawer. +  - Once the drawer is open, adjust the metal bars inside (they're magnetic) to be the correct spacing so that your PCB sits on their edges safely. Remove your PCB and press the right arrow key to close the drawer.  
-  - Navigate to "START PROF(down arrow key), and then start the profile with the right arrow key. +  - Navigate to START PROF” (down arrow key), and then start the profile with the right arrow key.  
-  - Once the oven has warmed up (a minute or two), the drawer will open. Place your PCB onto the pre-aligned bars. **BE CAREFUL - it'hot!** Press the right arrow key to close the drawer. +  - Once the oven has warmed up (a minute or two), the drawer will open. Place your PCB onto the pre-aligned bars. BE CAREFUL – they're hot! Press the right arrow key to close the drawer.  
-  The profile will run.  + 
-  - When it's completed, the drawer will open again. Carefully remove your PCB (**it's hot!**), and press enter to shut the drawer.+The profile will run. When it's completed, the drawer will open. Carefully remove your PCB (it's hot!), and press enter to shut the drawer.  
 + 
 +**Clockwise from top-left:** the oven with its computer; the drawer open with the magnetic metal bars and green thermistor wires; the front of the oven with the power button prominently featured; and the screen and the four arrow keys on top of the oven. 
 +{{ ::reflow-oven_4x1_2022-06.png?direct&800 |}} 
 + 
 +**Lead-free solder paste oven temperature profile** 
 +{{ ::hive_lf_profile_image.png?direct |}} 
 + 
 +**Leaded solder paste oven temperature profile** 
 +{{ ::hive_pb_profile_image.png?direct |}} 
 +---- 
 +===Advanced reflow use=== 
 +The reflow oven is a pretty simple tool, especially if you're using the standard recipes. However, the software allows additional functionalities to be taken advantage of. The software is called **FlowShow**, and can be launched from the main taskbar on the desktop to the right of the oven. The manual for the software is in the bookmarks bar of the Edge browser. 
 + 
 +{{ ::flowshow_mainwindow.png?direct&400|}} 
 +There are three tabs of operations. The main tab, "Profile recording", allows the user to monitor the temperature during tool use, and to record the temperature profile. **NOTE** that the "Start" button only starts the recording, //not// the process! Similarly, the "Stop" button does not stop the process, only the recording. There are seven temperature sensors in the tool: three are built-in, but four, the "Profile recorder" ones, are thermistors that can be positioned as desired within the oven itself, and can be useful for precision reflow processes where the temperature across the board is critical, or for sensitive components. These four can be found within the main oven drawer (the green wires; see image above). Be careful not to pull them too hard. Kapton tape is effective at keeping them in place over the duration of a process. 
 + 
 +The middle tab, "Profile programming", is where custom profiles may be created. **YOU MAY ONLY ADJUST PROFILE 12, "CHANGETHIS"!** Please do not mess with the other profiles at this time. Adjusting the profile is as easy as changing the numbers and times around, but if you do this without careful consideration sand knowledge, you can seriously damage or ruin your board and components outright.  
 +{{::flowshow_profileprogramming.png?direct&400 |}} 
 +Reflow can typically be separated into three stages: preheating, reflow, and cool-down. The machine has a built-in "optimized" heating ramp up that's given in the upper-right corner of the software. It's generally a good idea to follow this unless your process requires more rapid heating or cooling. Preheating brings the board and components and solder paste to a uniform temperature, and usually involves a soak at that temperature to ensure uniformity. The reflow is when the temperature is brought above the solder's liquidus point, where it transforms into a liquid. Most components don't like being that hot, so the amount of time at those high temperatures should be limited. Finally, there's a cool-down back to "ambient" temperature. Cooling-down too rapidly can also damage the board due to thermal shocks, so it's a good idea to leave this as is as well. 
 + 
 +The "Profiling assistant", seen right above the plot, can be used to see how your profile compares to the "standard" profile. Simply click on your board size (small is around 5-10 sq. in., medium is up to 25 sq. in., large is bigger than that) and click "Draw" to see the estimated profile.  
 + 
 +Once you have adjusted the parameters to your liking, press "Write One" to save and load it onto the machine. It //should// load as the current profile as well. Then you can run it as normal. 
 + 
 +**Write down the parameters as you set them for later!** Someone else may come and write over yours later. 
 + 
 +{{ :flowshow_admin.png?direct&400|}}
  
-**Clockwise from top-left:** the oven with its computer; the drawer open with the magnetic metal bars; the front of the oven with the power button prominently featured; and the screen and the four arrow keys on top of the oven. +The third tab, "Admin", has no useful options except for the "Virtual Mode" checkbox at the top. This allows you to test different profiles without actually running the toolThis was useful for me to make the profiles above, but frankly, I'm not sure when it may be useful to anyone else
-{{ ::reflow-oven_4x1.png?direct&600 |}}+
  
  • process_reflowoven.txt
  • Last modified: 2022/09/02 12:48
  • by benh