Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
pcb-tips [2022/06/25 14:48] – benh | pcb-tips [2023/09/05 13:37] (current) – benh | ||
---|---|---|---|
Line 1: | Line 1: | ||
==== Miscellaneous processing tips! ==== | ==== Miscellaneous processing tips! ==== | ||
- | //So you made a few boards. Or not! Either way, this is a running list of tips and tricks for users - things to do and things to avoid. We make no guarantee with any of these, but we have found that they' | + | //So you made a few boards. Or not! Either way, this is a running list of tips and tricks for users - things to do and things to avoid, in absolutely no order whatsoever other than the order in which we discovered them. This is basically the Institutional Knowledge of the LPKF equipment at The Hive. We make no guarantee with any of these, but we have found that they' |
* Plating is typically avoidable by making vias with a diameter of 40 mil (1 mm). A standard 0.1” header pin can then be pushed through and soldered on both the top and bottom. | * Plating is typically avoidable by making vias with a diameter of 40 mil (1 mm). A standard 0.1” header pin can then be pushed through and soldered on both the top and bottom. | ||
* Higher polygon isolation will reduce the chance of bridging to a plane during assembly (since we don’t really offer soldermask). However, it will also increase etch time because more of the substrate will be etched. " | * Higher polygon isolation will reduce the chance of bridging to a plane during assembly (since we don’t really offer soldermask). However, it will also increase etch time because more of the substrate will be etched. " | ||
- | * Slots! We can do them! There are probably | + | * Slots! We can do them! Here are a few methods for doing them: |
+ | * The best method | ||
+ | * If you have square slots with a minimum dimension of at least 1mm AND they do not need plating, you can add the slots in the same layer as the board' | ||
+ | * Plated square slots have not been demonstrated yet, but my guess would be that if they have a minimum dimension of at least 1mm, then you can use a similar method | ||
+ | * Overlapping | ||
* If you're interested in optimizing your ProtoLaser experience, see the [[https:// | * If you're interested in optimizing your ProtoLaser experience, see the [[https:// | ||
* Laser precision is dictated by many things, some (even many) of which are likely beyond your control as a user. Here is a completely-uncomplete list of some of these things (a * indicates things that you, as a user, will not be able to adjust, but get in touch if you think it's a major contributor to any issues you're seeing): | * Laser precision is dictated by many things, some (even many) of which are likely beyond your control as a user. Here is a completely-uncomplete list of some of these things (a * indicates things that you, as a user, will not be able to adjust, but get in touch if you think it's a major contributor to any issues you're seeing): | ||
Line 18: | Line 22: | ||
* Another suggestion for the laser would be to define a metric for etch quality using the aforementioned test design. That way, you can quantitatively determine which parameters are doing better than others. | * Another suggestion for the laser would be to define a metric for etch quality using the aforementioned test design. That way, you can quantitatively determine which parameters are doing better than others. | ||
* For the laser, if you're using a substrate thinner than 5 mil (0.125mm), tabs in your design are a near-requirement! You can make them in the laser. | * For the laser, if you're using a substrate thinner than 5 mil (0.125mm), tabs in your design are a near-requirement! You can make them in the laser. | ||
+ | * Laser cannot do two-sided jobs with plating by itself; the plotter is required for fiducials. No idea why. | ||
+ | * You can actually make boards with more required bits than the tool magazine has slots. It will yell at you about it, but just walk through the process as normal and it will ask you to put the bits into the magazine when it needs them. | ||
+ | * The LPKF sofware handles drill hits down to 0.2mm (7.5 mil) without any adjustments, | ||
[[pcb-book-of-kane|The Book of Kane]] | [[pcb-book-of-kane|The Book of Kane]] |