Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
pcb-help_pm [2021/01/15 11:34] – benh | pcb-help_pm [2022/03/02 22:48] – benh | ||
---|---|---|---|
Line 1: | Line 1: | ||
==== Knowledge Base: PROTOMAT ==== | ==== Knowledge Base: PROTOMAT ==== | ||
+ | {{ : | ||
=== Table of Contents === | === Table of Contents === | ||
- Overview | - Overview | ||
Line 9: | Line 10: | ||
- The tool exchange was botched! | - The tool exchange was botched! | ||
- The drill hits are incorrect, or the routing path was wrong! | - The drill hits are incorrect, or the routing path was wrong! | ||
+ | - I can't change the layer/ | ||
---- | ---- | ||
Line 30: | Line 32: | ||
More details regarding tool structure or usage can be found in the following documents: | More details regarding tool structure or usage can be found in the following documents: | ||
- | The Manual: [[https://drive.google.com/file/d/1BHTWPpFcI8OicYnVNza13r1TbDNCMBK2/view?usp=sharing|ProtoMat S-series Manual.pdf]]\\ | + | The Manual: [[https://gtvault.sharepoint.com/:b:/s/HiveMakerspace/Ef6YsYn1TMNHvpymUi-n3o4BjvqwKyH6vNf5HifMEC6PlQ?e=lzOcTx|ProtoMat S-series Manual.pdf]]\\ |
LPKF's " | LPKF's " | ||
- | The ProtoMat software (" | + | The ProtoMat software (" |
- | The vacuum system manual: [[https://drive.google.com/file/d/1b3VXgSC6Re8jisaGsmYYN9C9-cjXtuX4/view?usp=sharing|Dust Extraction Manual Jet Stream iSeries-e-1-0.pdf]]\\ | + | The vacuum system manual: [[https://gtvault.sharepoint.com/:b:/s/HiveMakerspace/ES_hmgB2275AkqsURJ-GiuMBEAEzU1wi5tpGmPj9EVE6-w?e=C5RqnA|Dust Extraction Manual Jet Stream iSeries-e-1-0.pdf]]\\ |
- | Our standard operating procedures: [[https://docs.google.com/document/d/1vTFJz3PAe3dHfptabhOmO4DTw_QN-n1ZShOumhzGG2k/edit?usp=sharing|ProtoMat S103 SOP]] | + | Our standard operating procedures: [[https://gtvault.sharepoint.com/:w:/s/HiveMakerspace/EcQvNGoNNa5AjiZ5wU1Vd8wBMPNk8mawFspeLrvNaG8VlQ?e=etuWny|ProtoMat S103 SOP]] |
---- | ---- | ||
Line 60: | Line 62: | ||
- The tool may have done something silly. | - The tool may have done something silly. | ||
In any of these cases, there is no good solution other than to restart the project and double check all of these (if possible) before starting to re-process. Sorry. | In any of these cases, there is no good solution other than to restart the project and double check all of these (if possible) before starting to re-process. Sorry. | ||
+ | |||
+ | * **I can't change the layer/ | ||
+ | Sometimes, for reasons unclear, a Gerber file gets automatically assigned to a undesired layer in the LPKF software on the ProtoMat, and cannot be changed. If this happens, what you need to do is highlight all the polygons on that layer in question that were imported, and move them to the correct layer (right click > Move to Layer). Highlighting a whole layer requires playing with the Layers pane on the left, and then click-and-drag across all the polygons. If there are things on that layer that are // | ||
+ | |||
+ | Details of this process can be found in [[https:// | ||