pcb-help_pl

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
Next revisionBoth sides next revision
pcb-help_pl [2021/01/19 13:22] benhpcb-help_pl [2021/10/08 12:43] – Added solution for cutting/drilling toolpaths madeline
Line 53: Line 53:
  
 ** Optimization **\\ ** Optimization **\\
-The ProtoLaser can be a very powerful tool. If you're working carefully with it, and you want to know more details about how the tool works, and how to better optimize your process, please see LPKF's [[https://gtvault.sharepoint.com/:b:/s/HiveMakerspace/EZGQyfhrC0BItpbSxd_rjRQBzDyNWUubu-RCuJr6a3OI9A?e=nbVu4k|Protolaser - Optimization.pdf]] document. This has proven to be useful for some users in the past. You can also contact LPKF directly at [[support@lpkfusa.com]].+The ProtoLaser can be a very powerful tool. If you're working carefully with it, and you want to know more details about how the tool works, and how to better optimize your process, please see LPKF's [[https://gtvault.sharepoint.com/:b:/s/HiveMakerspace/EZGQyfhrC0BItpbSxd_rjRQBzDyNWUubu-RCuJr6a3OI9A?e=nbVu4k|Protolaser - Optimization.pdf]] document. This has proven to be useful for some users in the past. You can also contact LPKF directly at [[lasersupport@lpkfusa.com]].
 ---- ----
 === Common processing errors === === Common processing errors ===
Line 63: Line 63:
  
   * **The bottom/top didn’t etch completely.**   * **The bottom/top didn’t etch completely.**
-You can either restart the process entirely (hit the Play button, see figure 32) or right click on “Top Side” (or “Bottom side”) under “Processing” on the left, and click “Process from here” to restart the top (or bottom) side processing with top (or bottom) side alignment.+You can either restart the process entirely (hit the Play button, see figure 32) or right click on “Top Side” (or “Bottom side”) under “Processing” on the left, and click “Process from here” to restart the top (or bottom) side processing with top (or bottom) side alignment. You can also do this for an individual tool or an individual tool for a single scan field.
  
   * **The board is/is not flipped in the Processing tab.**   * **The board is/is not flipped in the Processing tab.**
 On the left of the screen, make sure nothing is selected under “Processing”. If there is, hold down either CTRL (on Windows) or the command key (on Mac) and then left click to de-select it. If that doesn’t fix it, you can select either “Bottom Side” or “Top Side” (again, on the left) to force the correct orientation. You can try starting the project over again if this doesn’t solve it as well. Sometimes, the software has bugs. On the left of the screen, make sure nothing is selected under “Processing”. If there is, hold down either CTRL (on Windows) or the command key (on Mac) and then left click to de-select it. If that doesn’t fix it, you can select either “Bottom Side” or “Top Side” (again, on the left) to force the correct orientation. You can try starting the project over again if this doesn’t solve it as well. Sometimes, the software has bugs.
 +
 +  * **The toolpath generates drilling or cutting operations.**
 +Usually, this happens because the "supported by ProtoMat" box was not checked when you selected the template. Because the ProtoLaser does not know that you are using the ProtoMat for drilling and contour routing, it will try to do it itself. Reselect the template, making sure this box is checked.
  
   * **The software throws and "Insufficient pressure" error.**   * **The software throws and "Insufficient pressure" error.**
Line 75: Line 78:
     * //Potential issue:// The vacuum hose(s) may be clogged.     * //Potential issue:// The vacuum hose(s) may be clogged.
       * There are two vacuum hoses. One runs from the extraction hood (the round plastic bit inside the main bay) to the rear interior wall of the tool, and the second runs from the outside backside of the tool to the vacuum system (the tall white box to the tool’s right). You should be able to remove both of these and check for clogs.       * There are two vacuum hoses. One runs from the extraction hood (the round plastic bit inside the main bay) to the rear interior wall of the tool, and the second runs from the outside backside of the tool to the vacuum system (the tall white box to the tool’s right). You should be able to remove both of these and check for clogs.
 +    * //Potential issue:// If your substrate is very small, not enough of the bed may be covered for proper vacuum pressure.
 +      * Tape down an old piece of 8”x12” FR4 on the bed. Then, secure your sample inside one of the cutouts. If the FR4 has a lot of holes, try covering some of them with tape.
  • pcb-help_pl.txt
  • Last modified: 2022/07/18 18:06
  • by benh