Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
pcb-help_pl [2021/01/17 16:50] – benh | pcb-help_pl [2021/10/07 14:13] – Added solution to pressure error. madeline | ||
---|---|---|---|
Line 42: | Line 42: | ||
For more information, | For more information, | ||
The brochure: [[https:// | The brochure: [[https:// | ||
- | The Manual: [[https://drive.google.com/file/d/1BxVWaqscUSuwdxnlmrbbO0lq9QGHd9cX/view?usp=sharing| ProtoLaser U4 User Manual.pdf]]\\ | + | The Manual: [[https://gtvault.sharepoint.com/:b:/s/HiveMakerspace/EcM8MWAGR1tPu4dySYs2QRwBT9GmpSEZmcbCuVIBn2UfEA?e=DZws6y| ProtoLaser U4 User Manual.pdf]]\\ |
- | LPKF's " | + | LPKF's " |
- | Software guide: [[https://drive.google.com/file/d/1jqR5wxnQLJAZjezrfv-xtRAbVk5Unb49/view?usp=sharing|CircuitPro 3.0 PL - Software Guide.pdf]]\\ | + | Software guide: [[https://gtvault.sharepoint.com/:b:/s/HiveMakerspace/EY2hkxd8yeNLoB3t0B-_5rcB4rQPIgwmuCHR4CaHTTkFkQ?e=f6cddG|CircuitPro 3.0 PL - Software Guide.pdf]]\\ |
- | Vacuum system manual: [[https://drive.google.com/file/d/1hqnQRs0nk9Gr2x3jGlLfUgmQC5OFKuzb/view?usp=sharing|Dust Extraction Manual CSA 600 iSeries-e-1-0.pdf]]\\ | + | Vacuum system manual: [[https://gtvault.sharepoint.com/:b:/s/HiveMakerspace/Edt3AuJWGCBOkM6wxr56268BpM_O1znw6J4flrg26w2iow?e=AW6e4e|Dust Extraction Manual CSA 600 iSeries-e-1-0.pdf]]\\ |
- | Optimizing your process: [[https://drive.google.com/file/d/1rF-XXszzSLil9l0rhl82kTUsCyUagpYU/view?usp=sharing|Protolaser - Optimization.pdf]] | + | Optimizing your process: [[https://gtvault.sharepoint.com/:b:/s/HiveMakerspace/EZGQyfhrC0BItpbSxd_rjRQBzDyNWUubu-RCuJr6a3OI9A?e=5oMu0N|Protolaser - Optimization.pdf]] |
---- | ---- | ||
===Q & A=== | ===Q & A=== | ||
** Using a " | ** Using a " | ||
- | So you have a material that either isn't in the laser' | + | So you have a material that either isn't in the laser' |
** Optimization **\\ | ** Optimization **\\ | ||
- | The ProtoLaser can be a very powerful tool. If you're working carefully with it, and you want to know more details about how the tool works, and how to better optimize your process, please see LPKF's [[https://drive.google.com/file/d/1rF-XXszzSLil9l0rhl82kTUsCyUagpYU/view?usp=sharing|Protolaser - Optimization.pdf]] document. This has proven to be useful for some users in the past. You can also contact LPKF directly at [[support@lpkfusa.com]]. | + | The ProtoLaser can be a very powerful tool. If you're working carefully with it, and you want to know more details about how the tool works, and how to better optimize your process, please see LPKF's [[https://gtvault.sharepoint.com/:b:/s/HiveMakerspace/EZGQyfhrC0BItpbSxd_rjRQBzDyNWUubu-RCuJr6a3OI9A?e=nbVu4k|Protolaser - Optimization.pdf]] document. This has proven to be useful for some users in the past. You can also contact LPKF directly at [[lasersupport@lpkfusa.com]]. |
---- | ---- | ||
=== Common processing errors === | === Common processing errors === | ||
Line 75: | Line 75: | ||
* //Potential issue:// The vacuum hose(s) may be clogged. | * //Potential issue:// The vacuum hose(s) may be clogged. | ||
* There are two vacuum hoses. One runs from the extraction hood (the round plastic bit inside the main bay) to the rear interior wall of the tool, and the second runs from the outside backside of the tool to the vacuum system (the tall white box to the tool’s right). You should be able to remove both of these and check for clogs. | * There are two vacuum hoses. One runs from the extraction hood (the round plastic bit inside the main bay) to the rear interior wall of the tool, and the second runs from the outside backside of the tool to the vacuum system (the tall white box to the tool’s right). You should be able to remove both of these and check for clogs. | ||
+ | * //Potential issue:// If your substrate is very small, not enough of the bed may be covered for proper vacuum pressure. | ||
+ | * Tape down an old piece of 8”x12” FR4 on the bed. Then, secure your sample inside one of the cutouts. If the FR4 has a lot of holes, try covering some of them with tape. |