how-to-pcb

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revisionBoth sides next revision
how-to-pcb [2020/03/13 11:03] 143.215.93.31how-to-pcb [2020/03/13 11:14] 143.215.93.31
Line 4: Line 4:
 === Table of Contents === === Table of Contents ===
   - Introduction   - Introduction
 +    * Will the PIs at the Hive make a board for me?
 +    * What’s the process for getting trained?
 +    * What is SUMS?
 +    * How do I join a training session OR request a new one?
   - Training Sessions   - Training Sessions
 +    * What should I expect out of a training session?
 +    * Do I have to have any prior knowledge before coming to a training session?
 +    * How do I register for a training session?
 +    * I don’t see any training sessions available. Can I request one?
 +    * Are training sessions really 2-3 hours? Can I come late or leave early?
   - Quiz and Checkoffs   - Quiz and Checkoffs
 +    * What should I expect for the quiz?
 +    * What should I expect at a checkoff?
 +    * I don’t see the quiz! Where is it?
 +    * How do I schedule a checkoff?
 +    * I didn’t get a checkoff scheduled and all of my requested dates have passed. What now?
 +    * What if I don’t successfully complete the checkoff?
 +    * Can I bring my own design to fabricate instead of the training board for my checkoff?
   - Fabrication   - Fabrication
 +    * Process specifications 
 +    * Can I add soldermask or silkscreen?
 +    * Do I have to be with my board during the entire fabrication process?
 +    * Can I somehow reserve time on the equipment?
 +    * How long does it take to make a board?
 +    * How long does electroplating take?
 +    * Do the tools have additional capabilities?
  
 ----- -----
Line 50: Line 73:
 ----- -----
 === Training Sessions === === Training Sessions ===
 +
 **What should I expect out of a training session?**\\ **What should I expect out of a training session?**\\
 Training sessions cover the fabrication process of a basic 2-layer copper circuit board using the PCB plotter and PCB laser, as well as a discussion of the electroplating process for vias. Training sessions do not address board design or layout. For questions regarding design, find one of our PCB MPIs. Training sessions cover the fabrication process of a basic 2-layer copper circuit board using the PCB plotter and PCB laser, as well as a discussion of the electroplating process for vias. Training sessions do not address board design or layout. For questions regarding design, find one of our PCB MPIs.
Line 149: Line 173:
  
 ** Do the tools have additional capabilities? **\\  ** Do the tools have additional capabilities? **\\ 
-\\NOTE: The following capabilities are allowed in the spec of the tool, but we do not support these functions, meaning that our PIs and MPIs do not have experience with them, so you will be on your own if you attempt any of them!//\\+//NOTE: The following capabilities are allowed in the spec of the tool, but we do not support these functions, meaning that our PIs and MPIs do not have experience with them, so you will be on your own if you attempt any of them!//\\
 The ProtoMat has the capability to do aluminum and plastic 2-dimensional milling. The ProtoLaser can etch a very wide variety of substrates and films. The electroplater has the ability to do tin plating (though we don't carry the necessary solution by default). We also have the LPKF ProConduct system that enables manual electropating of individual vias for RF PCBs (proceed with caution here).  The ProtoMat has the capability to do aluminum and plastic 2-dimensional milling. The ProtoLaser can etch a very wide variety of substrates and films. The electroplater has the ability to do tin plating (though we don't carry the necessary solution by default). We also have the LPKF ProConduct system that enables manual electropating of individual vias for RF PCBs (proceed with caution here). 
  • how-to-pcb.txt
  • Last modified: 2021/01/11 14:04
  • by benh